Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
Hire a Pest Control Company Now
What're your thoughts on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a tub isn't precisely rocket science, but it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately difficult project. If the old bathtub is conveniently easily accessible, the job can move rapidly; if you have to open a wall to get rid of the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to move out the old bathtub as well as embeded in the brand-new one. Make certain you have qualified on your own for the task as well as are comfortable trying it. Instead of hiring a service provider to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This post will aid you mount a new bathtub in your washroom if you have already acquired a new tub and also don't require to alter the arrangement of your previous water pipes.
Your devices as well as product list should consist of the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome due to the limited access that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Secure the tap in place with the maker supplied backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The former kind must be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing both wood boards under its feet, put the tub in the needed setting. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To set up faucets, fit the bottom of the furthest flexible tap connector to the ideal supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water system as well as inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the tub and additionally examine the overflow outlet and the regular outlet for leaks.
Ultimately, take care of the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the bathtub should wait till the tub has been made use of at the very least once as this will resolve it into its final placement.
Getting ready for the Installation
To start with, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to stop stress on the bath tub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to fracture a rigid seal, creating the water to penetrate the wall surface in between the bath and also the tiling, leading to issues with wetness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to allow for the motion experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently readily available on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about A Step-by-Step Guide to Installing a Bathtub? Place a comment directly below. We would be delighted to listen to your opinion about this blog entry. We hope to see you back again in the future. In case you enjoyed our blog entry please do not forget to pass it around. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Course Detail Report this page